Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF

4
1411
Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF
Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF

Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF: Welcome To Tayari Jeet Ki. BTEUP Board Online Notes For Basic Electronics Engineering Branch With Subject Electronics Components And Devices (ECD).

2.5 ELECTRONIC COMPONENTS & DEVICES

Knowledge of Electronic components & devices is quite essential for a student of electronic engineering diploma programme. With the knowledge of these active and passive components he will work successful in every field of the branch.

Therefore a diploma student in electronics engineering must be equipped with the fundamental knowledge about electronic components, voltage and current source, semi conductor diode, transistors and FET for successful handling of industrial problems.

Introduction to Electronics Components And Devices
Introduction to Electronics Components And Devices

Introduction To Basic Electronics Components And Devices.

हैलो दोस्तो कैसे हैं आप सब आज के इस पोस्ट मे, आज हम इस पोस्ट मे ECD की PDF Notes देने वाले है और Basic Electronics Components And Devices मे पढे जाने वाले Chapters और उनके Topics को Discuss करने वाले है।

तो चलिये देखलेते है According To Syllabus Of Basic Electronics Components And Devices ECD इस Notes / Book मे क्या – क्या पढ़ना है  और आज का Objective भी यही है Introduction Of Basic Electronics Components And Devices, Basic Electronics Components And Devices का परिचिए तो आप इस पोस्ट को ध्यान से देखिये गा की आप ECD मे क्या पढ़ने वाले है। ठीक है

तो मेरा इस पोस्ट को लिखने के उदाशया यही है की introduction of ECD Basic Electronics Components And Devices क्यूकी ECD (Basic Electronics Components And Devices) को हम जानेंगे तो चलिये एक – एक कर के हम जानेंगे  इलेक्ट्रॉनिक्स का आध्यान करेंगे की इलेक्ट्रॉनिक्स का हमे Use कहा है और इलेक्ट्रॉनिक्स है क्या और इलेक्ट्रॉनिक्स कहा कहा उसे होता है।

Also Read : Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF

Up Polytechnic 2nd Semester ECD Basic Electronics Components And Devices Subject को पढ़ने पर आपको निम्न जांकरिया मिलेंगी…….

  • Indentify and distinguish between active components (BJT, FET etc) and passive components (Resistor, Capacitor, inductor etc).
  • Understand voltage and current sources as well as their inter-conversions.
  • Understand the working and application of semiconductor diode including half wave rectifier & Full wave rectifier.
  • Understand the working of BJT and hence able to design amplifier using it.
  • Compare various transistors biasing circuit and stabilize their operating points.
  • Understand the working of FET and hence able to design amplifier using it.
  • Compare BJJT, JFET, MOSFET & CMOS.
electronics engineering
Electronics Engineering

Detail List Of Chapter & Topic

  1. Introduction to Electronics (Electronics का परिचाए)

1.1 Application of electronic in different fields.

1.2 Brief introduction to active components and devices.

  1. Passive Components (इलेक्ट्रॉनिक अवयव)

Passive Components मे होता है जैसे

2.1. Resistor- Working characteristics/properties, Resistors-Carbon film, metal-film, carbon composition, wire wound and variable type (presets and potentiometers) constructional details, characteristics (size, voltage, tolerance temperature and frequency dependence) , noise consideration, specification, Testing, mutual comparison and typical applications, Voltage Dependent Resistor (VDR).

2.2. Capacitors- Working characteristics/properties, Capacitors-polyester, Metalized polyester, ceramic paper mica and electrolytic tantalum and solid aluminium types; construction details and testing, specifications, mutual comparison & typical applications.

2.3. Inductors, Transformers and RF coils- Working characteristics/properties Methods of manufacture of inductors, RF coils and small power and AF transformer and their testing, Properties of cores, Needs and type of shielding.

इन्हे भी देखे :- Applied Mechanics Notes PDF Up Polytechnic 2nd Semester

  1. Voltage And Current Sources (वोल्टेज और धारा स्रोत)

Voltage And Current Sources: इस सब्जेक्ट मे हम पढ़ेंगे वोल्टेज सोर्स क्या होता है ओर

3.1. Concept of constant voltage sources, symbol and graphical representation, characteristics of ideal and practical voltage sources.

3.2. Concept of constant current source, symbol and graphical representation, characteristics of ideal and practical current sources.

3.3 Conversion of voltage sources into a current sources & vice-versa.

3.4 Concept of floating and grounded D.C. supplies.

  1. Semiconductor Diode (अर्धचालक डायोड)

Semiconductor Diode इस बिषय मे हम पढ़ेंगे डायोड क्या होता है और Semiconductor मटिरियल मे आध्यान करेंगे और भी बहुत से ऐसे टॉपिक है जो आप नीचे देख सकते है।

4.1. P-N junction diode, Mechanism of current flow in P-N junction, drift and diffusion currents, depletion layer, potential barriers, P-N junction diode characteristics,  Zener& avalanche breakdown, Concept of junction capacitance in forward &  reverse bias conditions.

4.2. Semiconductor diode characteristics, dynamic resistance & their calculation from diode characteristics, dynamic resistance of diode in terms of diode current, Variation of leakage current and forward voltage with temperature (No derivations).

4.3 Diode (P-N Junction) as rectifier, Half wave rectifier, full wave rectifier including bridge rectifier, relationship between D.C output voltage and A.C input voltage, rectification efficiency and ripple factor for rectifier circuits, filter circuits- shunt capacitor, series inductor, bleeder resistance, working of the filter and typical application of each type.

4.4. Different types of diodes, characteristics and typical application of power diodes, zener diodes, varactor diodes, point contact diodes, tunnel diodes, LEDs and photo diodes

4.5. Important specification of rectifier diode and zener diode.

electronic repair vector
electronic repair

Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF

  1. Introduction to Bipolar Transistor

Introduction to Bipolar Transistor इसमे आप तर्न्सिस्टोर के बारे मे पढ़ेंगे और ट्रंजिस्टर कैसे काम करता है और bipolar के concept Introduction to Bipolar Transistor के कुछ भाग है जिसे आप नीचे देख सकते है।

5.1. Concept of bipolar transistor as a two junction three terminal device having two kinds of charge carriers, PNP an NPN transistor, their symbol and mechanism of current flow, explanation of fundamental current relations,

Concept of leakage current, effect of temperature on leakage current, Standard notation for current and voltage polarity.

5.2. CB, CE and CC configurations.

  1. Common base configuration (CB): input and output characteristics,

current amplification factor , determination of transistor parameters (input & output) dynamic resistance.

  1. Common emitter configuration (CE): current relations in CE configuration,

collector current in term of base current and leakage current (ICEO)

relationship between the leakage current in CB and CE configuration , input and output characteristics, determination of dynamic input and output resistance and current amplification factor β from the characteristics.

इसे भी देखे :-

Basic Electrical and Electronics Engineering Note Hindi Or English PDF

Applied Mathematics-2 PDF Free Download Up Polytechnic

Download Office Automation PDF Notes in Hindi Or English

UP polytechnic 2nd Semester Applied Physics 2 Notes | Engineering Physics PDF

  1. Common collector configuration (CC): Expression for emitter current in terms of base current and leakage current in CC configuration.

5.3. Comparison of CB and CE configuration with regards to dynamic input and output resistance, current gain and leakage current performance of CE configuration for low frequency voltage amplification, Typical application of CB configuration in amplification.

5.4. Transistor as an amplifier in CE configuration.

  1. DC load line, its equation and drawing it on collector characteristics.
  2. Determination of small signal voltage and current gain of basic transistor amplifier using CE output characteristics and DC load line, Concept of power gain as a product of voltage gain and current gain.
  3. Transistor Biasing And Stabilization Of Operating Point

देखिये सबसे पहले आती है Transistor Biasing, Biasing मतलब होता है उसको Operate करने का तरीका क्या है आखिर उसे बैटरि के साथ या फिर सर्किट के साथ कैसे कनैक्ट किया जाएगा तो इससे बाइसिंग बोलते है तो उसे ऑपरेट करने के लिए कितनी वोल्टेज दी जाएगी उसी हम पढ़ेंगे  And Stabilization Of Operating Point को

6.1. Different transistor biasing circuits for fixing the operating points, effect of temperature on operating point.

Need and method for stabilization of operating point.

Effect of fixing operating point in cut-off or saturation region on performance of amplifier

6.2. Calculation of operating point for different biasing circuits, use of Thevenin’s theorem in analyzing potential divider biasing circuit.

6.3. Simple design problems on potential divider biasing circuits.

Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF

  1. Single Stage Transistor Amplifier

और नैक्सट है हमारा Single Stage Transistor Amplifier, ट्रंजिस्टर का Use कर के Single Stage Amplifier पढ़ेंगे इसमे एक ट्रंजिस्टर का Use कर के अम्प्लिफिएर को अम्प्लिफ़ी करेंगे

7.1. Analysis of Single Stage CE, CB and CC amplifier.

7.2. Single stage CE amplifier circuits with proper biasing components.

  1. Field Effect Transistor (Fet)

और अगला है हमारा FET जिसका पूरा नाम है Field Effect Transistor क्या है नाम इसका Field Effect Transistor

8.1. Construction, operation, characteristics and Biasing of Junction FET.

8.2. Analysis of Single Stage CS,CG and CD amplifiers. (Only Brief Idea)

Circuit Symbols of Electronic Components
Circuit Symbols of Electronic Components

Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF

  1. MOSFET

और इसके बाद है हमारा MOSFET ये भी एक ट्रंजिस्टर फॅमिली का ही डिवाइस है इसका पूरा नाम है metal-oxide semiconductor field-effect transistor इसका फुल्ल फोरम होता है Metal-Oxide Semiconductor Field-Effect Transistor

9.1 Construction, operation, Characteristics and Biasing of MOSFET in both depletion and enhancement modes.

9.2 Analysis of Single Stage CS, CG and CD amplifiers. (Only Brief Idea)

  1. CMOS

और इसके बाद लास्ट है हुमरा Complementary Metal-Oxide Semiconductor (CMOS) तो इन सभी के बारे मे आप आध्यान करेंगे जिसमे कुल मिला कर 10 Chapters है।जिसमे आप बसिक्स – बसिक्स आध्यान करेंगे  और ये आपके 2nd Semester के ECD का first book है।

10.1 Construction, operation and Characteristics of CMOS in both depletion and enhancement modes.

10.2 Use of CMOS as Invertor, Different application of CMOS, CMOS IC.

10.3 Comparison of JEET, MOSFET and Bipolar Transistor.

और इसके नीचे हमने आपको दिया है प्रकटिकल के लिस्ट जिससे आप को ECD 2nd Semester मे आध्यान करने होंगे इनमे कुल प्रकटिकल 14 है जिसमे से आपको को आपके अध्यापक द्वारा दिये गए निर्देशों का पालन कर के प्रकटिकल को रैडि करने होंगे जो की है

Basic Electronics Up Polytechnic 2nd Semester ECD Notes In PDF

List Of Practical in Electronics Components And Devices
List Of Practical in Electronics Components And Devices

List Of Practical In Electronics Components And Devices

  1. Identification of types of packages, terminals and noting different ratings using data books for various types of semiconductor diodes (Germanium, point contact, silicon low power, high power and switching diode).
  2. Familiarization with lab instruments (Multi-meter/CRO), etc.
  3. Testing of various passive and active components.
  4. Plotting of forward V-1 characteristics for a point contact and P-N junction diode (Silicon & Germanium diode).
  5. To Plot forward and reverse V-I characteristics for a zener diode.
  6. Rectifier circuits using semiconductor diode, measurement of input and output voltage and plotting of input and output wave shapes.
  7. i) Half wave rectifier
  8. ii) Full wave rectifier (centre tapped and bridge rectifier circuits)
  9. To Plot wave shapes of a full wave rectifier with shunt capacitor, series inductor and filter circuit.
  10. To Plot the input and output characteristics and calculation of parameters of a transistor in common base configuration
  11. To Plot input and output characteristics and calculation of parameters of a transistor in common emitter configuration.
  12. Transistor Biasing circuits
  13. i) Measurement of operating point (Ic&Vce) for a fixed bias circuit.
  14. ii) Potential divider biasing circuits. (Measurement can be made by changing the transistor in the circuits by another of a same type number).
  15. Objective for Plotting the FET characteristics and determination of its parameters from these characteristics.
  16. Measurement of voltage gain at 1 KHZ for different load resistance for a BJT amplifier circuit.
  17. Measurement of voltage gain for a JFET amplifier circuit.
  18. Measurement of voltage gain for a MOSFET amplifier circuit.
Book Recommended for Electronics Components And Devices 2nd Semester of Polytechnic
Book Recommended for Electronics Components And Devices 2nd Semester of Polytechnic

Books Recommended For Up Polytechnic 2nd Semester ECD Subject

  1. Bhargava, Kulshreshttha& Gupta – “Basic Electronics& Linear Circuits” – Tata Mcgraw-Hill.
  2. Malvino, A. P.-“Electronics Principles” –Tata Mcgraw-Hill
  3. Robert.L.Boylestad – “Electronic Devices & Circuits Theory” – Pearson Publication.
  4. V.K.Mehta- “Principles of electronics” – S.Chand Publication.

दिये गए लिंक पर क्लिक करे और डौन्लोड करे अपने PDF नोट्स hindi और English लैड्ग्वेज मे

तो उम्मीद है आपको मेरे द्वारा दी गई जानकारी अच्छी लगी होफ़ी और अगर अच्छी लगी हो गी तो मेरे इस वैबसाइट के bell icon को दबाए जिससे आपको आपके सब्जेक्ट और ब्रांच के जानकारी सबसे पहले मिले गी और

मेरे प्यारे दोस्तो अगर आपको ऐसे ही पेपर, नोट्स अथवा और कोई भी सब्जेक्ट का आध्यान के लिए हमारे वैबसाइट पर विजिट करते रहें…….

दोस्तो अगर मैंने कही गलत लिखा है या कुछ भूल गया है लिखना तो कृपया हमे माफ करे और

अगर आपके मन मे कोई सुझाव हो या कोई प्रश्न है तो कृपया कमेंट ब्बोक्स मे कमेंट कर सकते हैं और

अगर आप हमे कुछ सुझाव अथवा प्रतिकृया देना चाहते हैं तो नीचे दिये हुए कमेंट बॉक्स मे कमेंट करें…. आपका सुझाव हमारे लिए महत्व और कल्याणकारी होंगे…

धन्यवाद 😊

4 COMMENTS

LEAVE A REPLY

Please enter your comment!
Please enter your name here